Home / Single phase water pump foot valve submersible pump specifications

Single phase water pump foot valve submersible pump specifications

REQUEST A QUOTE

200 Series Submersible Effluent Pump

The submersible pump shall be capable of handling solids enabling pumping over long distances in pipelines as small as 1.5" in diameter. The submersible pump shall have a shut-off head of 130 feet and a maximum flow of 102 GPM @ 10 feet of total dynamic head. The pump shall be controlled with: _____A piggy back style on/off float switch.200 Series Submersible Effluent Pump specified herein. The pump models covered in this specification are Series FL200 single phase or three phase effluent pumps. The pump furnished for this application shall be model _____as manufactured by Liberty pumps. 2.01 OPERATING CONDITIONS: Each submersible pump shall be rated at 2 hp_____ volts _____ phase 60 Hz. 3450 RPM.Appendix 11: Example Pump Station CSI Specifications Jan 04, 2008 43 21 39 Submersible Pumps Constant Speed 43 21 43 Submersible Sump Pump . EXAMPLE ONLY Motor Control Centers 26 24 19 South Park Pump Station and Water Quality Facility Page 1 of 9 SECTION 26 24 19 MOTOR CONTROL CENTERS A. Motor control centers shall be rated 600 volts, 60 Hertz, 3 phase, 3 wire as specified and shall be

Carry Powerful High Volume Submersible Pump CP610-12

Prices are for 230 volt, single phase pumps, please call for pricing on 3 phase motors; Unlike regular centrifugal pumps which can be valved back to reduce the flow. Axial-flow pumps need to be able to get rid of all the water they can produce. It is for this reason that it is important to use the correct size plumbing and to never valve backFranklin Submersible 4" Motor 3/4 HP 230 Volts 1 Designed for use with Franklin 3-wire single-phase submersible motor 3/4 HP 230 Volts 1 # 2145079004. Type 3R enclosure for outdoor mounting, not gasketed, two holes for wall mounting at back of box. Has knockouts in the bottom and sides. 5 terminals are provided for wiring up to #10 AWG wire. UL recognized and CSA certifiedGoulds 10HS05422C, 10GPM, 1/2HP, 230V, 2 Wire, 4" HS The Goulds Water Technology HS series 4 submersible pumps feature top quality materials and construction to provide reliable and efficient service. HS series 4 submersible pumps are available in 5, 7, 10, 18 and 25 gallon per minute sizes equipped with 1/2 hp to 1 1/2 hp motors.

How to Diagnose a Bad Foot Valve in a Submersible Well Pump

A foot-valve is only used in a jet-pump situation (where the pump resides above ground and shoots some water down the well to help lift more water back up). In a submersible pump situation, it is technically called a check-valve because it sits immediately above the pump rather than below, but it is commonly referred to as a foot-valve andPump Specifications - Ferguson herein. The pump models covered in this specification are Series LE100 single phase or three phase pumps. The pump furnished for this application shall be model _____as manufactured by Liberty pumps. 2.01 OPERATING CONDITIONS: Each submersible pump shall be rated at 1 hp_____ volts _____ phase 60 Hz. 1725 RPM.INSTALLATION AND OWNERS MANUAL - Dab Pumps TECHNICAL SPECIFICATIONS Single phase power-supply voltage 115V or 230V Voltage variation tolerance +/-10% Frequency 50-60 Hz Full load amp rating 115V(230 V) 16 FLA (20 FLA)Myers Ranger Submersible Water Well Pump 50 GPM 5 HP 230V Specifications. Includes: Myers # SS50-50 pump end, # 2243038602 5 HP Franklin 4" 230 volt single phase motor, # 2821138110 Control Box, # HS4 Cable Slice Kit and # CAP-22 2" Check Valve Construction: Stainless steel discharge bowl, suction bowl, pump shell, suction screen, shaft, coupling and lead guard. Engineered thermoplastic staging. Buna-N shaft bearing.

Myers Ranger Submersible Water Well Pump 80 GPM 3 HP 230V

Specifications. Includes: Myers # SS30-80 pump end, # 2243022604 3 HP Franklin 4" 230 volt single phase motor, # 2823028110 Control Box, # HS4 Cable Slice Kit and # CAP-22 2" Check Valve Sold as components (not assembled). Other accessories available and sold separately Check Valve: Separate poppet type Inlet: Screened inlet Outlet: 2" FNPT.Stages: 9 Electrical: 230 volts, 1 phase, 60 Hz, 3 HPMyers Ranger Submersible Water Well Pump 80 GPM 5 HP 230V Specifications Includes: Myers # SS50-80 pump end, # 2243038602 5 HP Franklin 4" 230 volt single phase motor, # 2821138110 Control Box, # HS4 Cable Slice Kit and # CAP-22 2" Check Valve Construction: Stainless steel discharge bowl, suction bowl, Pentair STA-RITE Submersible & Centrifugal Pumps Sta-Rite DPC Centrifugal Pump, Medium Head Centrifugal Pump, 1/2 HP, 43 GPM, 115V, 1 Phase, 1-1/4" Suction & Discharge. The DPC Series self-priming centrifugal pump is a rugged cast iron pump capable of priming up to 20' vertically and will handle solids up to 0.225" diameter. 1 product.

Pump Specifications - Ferguson

The single phase pumps shall have a unitized carbon / ceramic seal with stainless steel housings and spring equal to Crane Type 6A. Three phase pumps shall have silicon carbide seals. The motor plate / housing interface shall be sealed with a Buna-N o-ring. 8.01 IMPELLERSUBMERSIBLE MOTORS - North America Water The application has 160 feet of #10 AWG copper wire installed. Using the formula below, 160 feet (actual) 300 feet (max allowable) is equal to 0.533. This means 53.3% (0.533 x 100) of the allowable voltage drop or loss, which is allowed between the service entrance and the motor, occurs in this wire.SUBMERSIBLE PUMPS - North America Water SUBMERSIBLE PUMPS 4" TRI-SEAL HIGH CAPACITY PUMPS FEATURES MODEL NO. EXPLANATION Four performance ranges: 35, 45, 60, and 90 gpm 2" NPT discharge, with and without an internal stainless steel wafer-style check valve Stainless steel discharge head and motor bracket High flow hydraulic staging allows for maximum pump output, exceeds all energy

SUBMERSIBLE PUMPS - North America Water

The 3200 Series submersible pumps are designed so that all parts of the pump end, including the cable guard, fall within the diameter of Franklin Electrics industry leading submersible 4" motor. This reduced diameter pump end makes it ideal for installations where the well is considered encrusted or tight in comparison to a standard 4" well.Simmons Manufacturing Product Catalog All foot valves furnished with Buna-N O-Ring, stainless steel spring and stainless steel locknut. All valves 3/4 through 1-1/2 have a working pressure of 400 psi. All valves 2 and larger have a working pressure of 600 psi. 190 Maximum Temperature Rating *Silicon bronze components contain less than .05% (1/20 of 1%) Lead. WeightSubmersible Motors - Franklin Electric locked rotor amps listed on page 13 (single-phase) and pages 16-17 (three-phase). Use of Check Valves It is recommended that one or more check valves always be used in submersible pump installations. If the pump does not have a built in check valve, a line check valve should be installed in the discharge line within 7.5 metres

Submersible Pump Sizing & Selection

Q: Ive selected my pump. Am I done yet? A: Not quite. Your pump needs electricity to work. If theres no power on site, you need to spec a generator: Most submersible pumps with 5HP or less are 230V/single phase. Youll need 1.5kW per motor HP Soa 5HP pump needs a minimum of 7.5kW You also need to spec the right power cableSubmersible Water Pump Types And Specifications May 05, 2016 Parts of Submersible Water Pump 5. Applications of Submersible Water Pump Submersible pumps are found in many applications. Single stage pumps are used for drainage, sewage pumping, general industrial pumping and slurry pumping. They are also popular with pond filters. Multiple stage submersible pumps are typically lowered down a borehole and most typically used for residential, commercial, municipal and industrial water extraction (abstraction), water Use of Check Valves in Submersible Well Pump Installations Jan 16, 2019 It is recommended that at least one check be installed in all submersible well pump installations. Many well pumps have built-in check valves. Even if a pump does have a built-in check valve, we recommend that a check valve be installed in the discharge line within 25 feet of the pump and below the draw down level of the water supply.

Voltage Drop and Submersible Pumps - Empowering Pumps

Oct 09, 2011 Example 4: Voltage Drop in Single Phase Application 2*0.00279Ohms/ft*250ft*29Amps = 40.5Volts In this case, the power loss is 587Watts, or 0.79hp, in the cable, the voltage at the motor and undervoltage are both 189.5 Volts and 17.6%. The result is a needed change in cabling and recalculation of voltage drop with the new wire size.Water Pumps Specifications Engineering360 In general, a ram pump can pump approximately one tenth of the received water volume to a height ten times greater than the intake. A hydraulic ram pump is useful where the water source flows constantly and the usable fall from the water source to the pump location is at least 3 ft. Split Case Pumps

Maybe You Will Be Interested